Covers complete tear down and rebuild, pictures and part diagrams, torque specs, maintenance, troubleshooting, etc. Production model years:1985, 1986, 1987, 1988, 1989. However, the spark plug should be tightened to the specified torque as soon as possible. To install the panel 1. Unlike other manuals on the internet my manuals don't need a password to view or print and you can back them up any way you see fit to make sure it's aways there when you need it.
After draining the coolant, thoroughly flush the 7. This will ensure that Yamaha Motor Corporation, U. That can make your Yamaha are no mileage limitations. For When in reverse, the reverse indicator light this reason, you should read the following material should come on. Insert a new bulb into the bulb holder, push it in, and then turn it clockwise until it stops. Brake pedal free play If the correct free play cannot be obtained, have a Yamaha dealer adjust it.
Remove the final gear oil filler bolt, final gear oil level check bolt, and the final gear oil drain bolt to drain the oil from the final gear case. If soft or spongy, have Yamaha dealer bleed hy- draulic system. Remove the front carrier by removing the bolts. Rear storage compartment cover 1. Panel G Panel G 2.
This manual is also a very reliable source of information that will make you, in time know more and more about your vehicle and how to prevent future problems from happening!! Air filter case holder 2. Pull outward on the areas shown. Remove the sponge material and the mesh 2. If the indicator light does not come attempt. Remove the tailpipe, by pulling it out of the 3. Could cause carbon monoxide poisoning, possibly leading to death.
Applying the brakes or accelerating is not Skidding or sliding improperly. Do not attempt to diagnose such problems yourself. To charge the battery Have a Yamaha dealer charge the battery as soon as possible if it seems to have discharged. Remove the dipstick, and then wipe it off with a clean rag. Tap the tailpipe lightly, and then use a wire into the muffler and align the bolt holes. When braking described in this manual.
Yamaha Atv Yfm 7fgpw 2000 2009 Factory Service Repair Manual Download This circuit diagram shows the entire functioning of the circuit. Before riding, check that the brake fluid is above the minimum level mark and replenish if neces- sary. We will be recommending you to others!! V-belt case drain plug 1. If the engine overheats again, have a The coolant level Yamaha dealer check and repair the cooling system. It is fully printable, print 1 page, 1 chapter or print the entire manual and put it in a 3-ring binder.
Insert the dipstick completely into the oil filler The engine oil should be between the minimum hole, and then remove it again to check the oil and maximum level marks. Have a Yamaha dealer replace the stabilizer bush- es if necessary. If the warning the warning light is on may cause damage to light does not come on, have a Yamaha dealer the engine. If there is prior to operating the engine for the first time. To install the panel Panels D and E 1. I expected a few days for a response, not minutes. Most of its essential components and connections are illustrated by graphic symbols arranged to spell it out operations as clearly as is possible but without regard towards the physical form of the various items, components or connections.
Turn the adjusting ring in direction a to increase the spring preload and thereby harden the suspen- sion, and in direction b to decrease the spring preload and thereby soften the suspension. Check the ter- ways follow the inspection and maintenance rain carefully before you start up any hill. Front carrier stay bolt 1. Remove the rear carrier by removing the bolts. Remove the front carrier stays by removing the bolts. Fuel tank cap cover 4. To prevent burns, avoid touching the exhaust system.
For more in- plug, and then place the spark plug on the formation on storing the battery, see page cylinder head so that the electrodes are 8-55. Thank you ever so much for your fast replies, excellent products, and perfect service. This could distract the operator and increase the risk of losing control and causing an accident. Install the new oil filter cartridge with an oil fil- ter wrench, and then tighten it to the specified 9. Install the bulb holder together with the bulb by turning it clockwise. It is specifically written for the do-it-yourselfer as well as the experienced mechanic. To access the storage com- partment, remove the storage compartment cover.