Keep all parts away from any source of fire. Adler adly adly 150 thunderbike parts adly 150 utilitaire parts adly 300 rs parts adly atelier300 2004 service. Install: S upper bracket S washer S steering stem nut 110 Nm 11 mSkg, 80 ftSlb 4. Connect the pressure gauge 1 and adapter 2 onto the fuel injection pipe. The manufacturer cannot be held responsi- ble for property damage or personal injury that may result from improper handling of the rear shock absorber. S Do not mix different types of antifreeze.
Connecting rod nut 15 Nm 1. Tighten: S connecting rod bolts 15 Nm 1. Stand the motorcycle on a level surface. Measure: S radial wheel runout 1 S lateral wheel runout 2 Over the specified limits! Measure: S brake disc thickness Measure the brake disc thickness at a few different locations. Loosen the bleed screw and push the brake caliper pistons into the brake caliper with your finger. Measure: S commutator diameter a Out of specification! Disconnect: S lead S coupler S connector 2.
S Do not smoke, and keep away from open flames, sparks, or any other source of fire. S Malfunction in pickup rotor. Lubricate: S inner rotor S outer rotor S oil pump shaft with the recommended lubricant Recommended lubricant Engine oil 2. Headlight beam is Direction lowered. Stand the motorcycle on a level surface. Remove: S screw plug 1 S brake pad pin 2 S brake caliper 3 S brake pad spring 4 2. Install: S brake master cylinder kit S circlip S dust boot 2.
Setting the diagnostic mode 1. B1 X B4 Order Inspection operation item and probable Operation item and countermeasure Reinstatement. Replace the brush springs as a set. S If any connection on the hydraulic brake system is disconnected, the entire brake system must be disassembled, drained, cleaned, properly filled, and bled after reas- sembly. Check: S throttle cable free play a Out of specification! Repair or replace any faulty part.
Er-4 Symptom Non-registered data has been received from the meter. The slot is worn or broken! The resistance does not change or it changes abruptly! Round off the original valve pad number ac- cording to the following table. Make sure that the timing chain tensioner rod comes out of the timing chain tensioner housing smoothly. Replace: S rear wheel sprocket a. Measure the camshaft journal diameter. Remove the valve guide with the valve guide remover 1. Brake pad Brake caliper piston Brake caliper piston seal.
Measure: S ten-link section a of the drive chain Out of specification! Replace: S bearing balls S bearing races a. Measure: S camshaft-journal-to-camshaft-cap clear- ance Out of specification! Voltage should be measured 30 minutes after the machine is stopped. Remove the seat fuel tank. Stand the motorcycle on a level surface. Screw plug Brake pad pin Brake pad. Battery S Check the condition of the battery. Grip end Handlebar grip left Clutch switch connector.
If the crankshaft-journal-to-crankshaft-jour- nal-bearing clearance is out of specification, select replacement crankshaft journal bear- ings. Check: S brake fluid level Below the minimum level mark a! S Turn the crankshaft counterclockwise several full turns to seat the parts. Measure: S valve stem runout Out of specification! Measure: S crankshaft runout Out of specification! Check: S lead S coupler S connector Moisture! Install: S starter motor yoke 1 S O-ring 2 S front cover 3 Srear cover 4 S bolts 5 3. Other brake fluids may cause the rubber seals to deteriorate, causing leakage and poor brake performance. After all of the bolts are fully loosened, remove them. Put a mark 1 on the corner of the connecting rod nut 2 and the connecting rod cap 3. S Connect the pocket tester Ω coupler from the wire harness.
While lightly pressing the timing chain ten- sioner rod by hand, turn the tensioner rod ful- ly clockwise with a thin screwdriver 1. After the bolt or nut has been tightened to specification, bend the lock tabs along a flat of the bolt or nut. Start the engine, warm it up for several min- utes, and then turn it off. S Measure the ignition spark gap Spark plug cap resistance S Crank the engine by pushing the starter. Compression pressure with oil applied into the cylinder Reading Diagnosis Higher than. Check: S radiator 1 S radiator inlet hose 2 S radiator outlet hose 3 S oil cooler 4 S oil cooler inlet hose 5 S oil cooler outlet hose 6 S water jacket outlet joint 7 S water jacket hose 8 S water pump outlet pipe 9. Check: S clutch cable free play a Out of specification! Lubricate: S bearings S spacer S dust covers S pivot shaft Recommended lubricant Lithium-soap-based grease 2.
The oil level warning light fails to come on. See page 7-32 S Replace any damaged parts if necessary. Voltage should be measured 30 minutes after the machine is stopped. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Check: S O-rings 1 Damage! Intake valve lifter Intake valve pad Intake valve cotter Intake valve upper spring seat Intake valve spring outer Intake valve spring inner.