Kc hilites wire harness. KC HiLiTES Wiring Harnesses 2019-01-29

Kc hilites wire harness Rating: 5,9/10 1203 reviews

KC HiLiTES 5th Gen 4Runner Ditch Lights

kc hilites wire harness

When you install extra lighting on your Jeep you expect it to be tough and reliable otherwise, why have it? I just got a switchpros and looking forward to install some lights. You do not need to remove both bolts from the hood in order to install the brackets. Step 19C: Bottom of A-Pillar Once you get both wires down through the weather stripping, it should look something like this. There is no relay required and the switch is illuminated and comes with a panel. Give every connection in your harness a good tug and make sure every connection is nice and secure.

Next

KC HiLiTES Wiring Harnesses

kc hilites wire harness

I have been a t4r. You will receive notification of your enrollment in the extended product warranty program via email within 24 hours of placing your order. Fitment: 1987 1988 1989 1990 1991 1992 1993 1994 1995 1997 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 Word On The Trail Never had anything but the best on line experience with Extreme Terrain. The benefits available under this Limited Warranty are strictly provided to you for the replacement of the Covered Part s which fails due to a defect. If you for this job, it would help.

Next

KC HiLiTES Jeep Wrangler Wiring Harness for 2 Lights w/ 2

kc hilites wire harness

Repeat this step with the second bolt until the bracket is secure. Towards the end, we are going to replace with new double sided 3M tape. Again, see below for the final harness. For a quick lighting test, you can temporarily twist both wires together and hold them in place with a set of alligator clips. .

Next

KC HiLiTES Jeep Wrangler Wiring Harness for 2 Lights w/ 2

kc hilites wire harness

The Ultimate 5th Gen 4Runner Ditch Light Options? Shown above is our final harness length. Throughout our website and catalogs these terms are used for identification purposes only. I did the install alone. As with all wiring it is recommended that you double check all of your connections to make sure they are secure and properly wired. Beam Pattern:  90° Spot or  12° Flood. Here is what I came up with.

Next

KC HiLiTES 5th Gen 4Runner Ditch Lights

kc hilites wire harness

You'll see it on the item page as a Vendor Handling fee, and it will show up in the cart below the item s you're ordering. Repeat this process on the opposite passenger side of your 4Runner and you are all set. Step 3: Cut Power and Ground from Harness Cut the positive and ground wires free from the relay section of the harness. The kits come with your wiring harness, lights, switch, hardware and brackets. The rest of the kit was not used. If your covered part fails whtin the extended warranty time from, simply call the program administrator at 1-844-870-4881 for instructions before any repairs or replacements have begun.

Next

hilites « Wire Wiring Harness

kc hilites wire harness

Please save this email for possible future reference. Somewhere around there should get you close though. Measure the final harness and then add a waterproof connector on the end of the ground wire. Note: There is a small clip that attaches to the hood brackets, you need to pop this out with some needle nose pliers, install the ditch mount bracket and then reattach the clip. This relay is a complete kit and setup for 2 high powered lights. A big piece of reliability is how that system is wired, the wiring harness used and the connectors involved.

Next

KC HiLiTES Jeep Wrangler Wiring Harness for 2 Lights w/ 2

kc hilites wire harness

Step 16: Pull up Weather Stripping The weather stripping is held in place by little rubber to body clip and on the end, and some double-sided tape. Country Of Origin: United States. This allows for an easy feed for the harness up under the hood and along the weather stripping. We are wiring our ditch lights to. Great job here man, really.

Next

KC HiLiTES Jeep Wrangler Wiring Harness for 2 Lights w/ 2

kc hilites wire harness

You can use this wiring harness kit on any existing auxiliary lighting system to get more lights powered up. I wanted the lights to disperse light in a wide, flat pattern, creating more side-to-side coverage, and less distance coverage. Overview of provided wiring harness Start by mapping out the harness to get an idea of the length and placement in your engine bay. Remove sleeve from provided harness Start by removing the black sleeve around the red, black, and yellow harness. Remove the electrical tape surrounding the entire harness and then another section surrounding the ground. This was to keep everything intact. Step 2: Wiring Harness Disassembly for Switch Pro Start by separating the wires in the kit.

Next

hilites « Wire Wiring Harness

kc hilites wire harness

With the help of a friend and no documentation photos , your install should take 2-3 hours, if that. A Covered Part has failed when it can no longer perform the function for which it was originally designed solely because of its condition and not because of the action or inaction of any non-covered parts. This article among many others, I have learned something from and will continue to follow your work. This is one seriously impressive light bar. The low profile ditch light brackets sit very close to the hood of the 4Runner.

Next