Discon- by a reputable radiator repair shop. The camshaft rotates mounted at the underside of the block opposite the within four bearings. Then close each bleed screw as fluid starts to drip from it. Check for excessive foam on dipstick after normal driving. Insert pli- ers into clutch hub. The rear wiper arm is mounted directly to the motor output shaft.
Tighten nuts to 11 N·m 8 ft-lbs ence marks. Note position of fitting before removal. Use small center punch or scriber to make alignment marks. The plunger and valve must always be fitted to the original body. Slip bypass hose from water pump while removing pump from vehicle. Fuel Tank Skid Plate Nuts. Also check connection to brake vacuum booster.
Sub- Using the wrong lubricant will cause overheating tract this amount from original shim. El Club de Diagramas es donde los técnicos intercambian y comparten Diagramas, Manuales de Servicio y todo archivo de información técnica útil para las reparaciones electrónicas. C372 Left Rear Quarter Panel C433. Remove throt- pedal to check for any binding. Use wood hammer handle or rawhide mallet to seat assembly if necessary.
Tighten cover 8 Install 1-2 and 2-3 valve governor plugs in plate screws to 4 N·m 35 in. G103 Right Side of Engine G108 Front of Left Fender Block 4. Set air gap to 0. Damaged plate separators can charge by measuring the specific gravity of the elec- cause early battery failure. At 55°C 140°F , the sensor resistance is 2. Turning the adjusting screw counterclockwise increases pressure while turning the screw clockwise decreases pressure. Install all main ing cap.
When gasket makes contact with sealing surface, Fig. Insert pli- drum for assembly alignment reference Fig. Length 3 Install the relief valve and spring. Ensure cup is correctly seated. Group 0, Lubrication and Maintenance, contains general maintenance information in time or mileage intervals for ignition related items. Fan belt removal is not neces- sary as the water pump studs will hold the pump pulley in position. Throttle Body Inspect for pinched, cracked or leaking fuel hoses.
This Service Manual has easy-to-read text sections with top quality diagrams and instructions. All pages are printable, so run off what you need and take it with you into the garage or workshop. Install a snap ring upright in the bearing assembly Fig. Differential bearing preload and ring gear backlash is adjusted by the use of spacer shims positioned between the side bearing race and the housing. Heat the joint until the tubing is tightly sealed and sealant comes out of both ends of the tubing.
Spark length of all spark plug cables. It is grounded by the 3. Doing so may dam- in the starter. Reduced bulb life will result. Tighten the bolts to 11 N·m 95 in. Grasp the boot not the cable and pull it off with a steady, even force. If major components such as the over- and forth and tilt it inward to remove it from case.
Tap bearing out from inside of case with brass drift and hammer. Remove drain plug and drain lubricant remaining in case. Recheck the fuel line connection. These special service tools or their equivalent, if not obtainable through a local source, are available through the following outlet. In operation, the Trac-lok clutches are engaged by two concurrent forces. Second Edition Manuály uživatelské 5.
Third Edition User's manuals 4. Hose clamp screws must be facing towards rear of vehicle. An 11 mm socket is required. Plastigage is soluble in oil. For circuit descriptions and diagrams, refer to The motor contains a self-resetting circuit breaker 8W-63 - Power Seat in Group 8W - Wiring Diagrams.
Rotate slinger and tap at four positions 90 degrees apart to remove it. When using Plastigage, check only one bearing The clearance indicate with the 0. The filter is located under the vehicle near the fuel tank Fig. Tighten clamp screw to 10-12 N·m 90-110 Verify that switch operating lever fingers are cen- in. The regulator is calibrated to maintain a constant pressure at the fuel pump module outlet fitting of 338 14 kPa 49 psi 2 psi. Movement of the valve pushes the switch plunger upward.