As you can see, downloading Eton Beamer Matrix Service Manual pdf or in any other available formats is not a problem with our reliable resource. Unscrew the two fixing screws of the body cover under the middle cover. New vehicles sold by an authorized dealer to original retail consumers are covered by this policy for a period of six 6 months from the date of delivery. Remove the cylinder bolt nuts. If your starter motor will not turn over and the battery is fully charged, check the inline fuse on the unit. Disassemble the float arm pin, float and float needle valve. Riding in unusually dusty areas may require more frequent servicing.
Limit: Replace if the swing is over 2. Replace the cylinder head gasket. Remove the rear handle bar. This Starting Procedure period allows the engine parts to seat and wear properly without undue strain which can cause The following procedure must be followed premature failure. Torque when installing a handlebar: M6 nut: 7 - 9 lbf-ft M10 nut: 22 - 29 lbf-ft 8.
Disconnect the fuel line and auto-choke electric wire. This free play should be 5-10mm. Remove the filter element from the air box. Engine Manual Choke Lever The engine choke lever is used to enrich the fuel mixture when starting the engine from a cold start. What you will also be glad to hear is that our professional customer support is always ready to help you if you have issues with a certain link or get any other questions regarding our online services. When carrying a passenger, always It is not recommended to operate this vehicle insure that they place their feet on the passenger in slippery conditions such as on snow or ice pedals.
Language: English Category: Eton Publish: February 28, 2019 Source:. Remove the bolt at the low end of the rear shock. Start by moving the lever to the left to choke the engine. Remove the cap from the spark plug. The torque Cam is loaded from the outside. Unscrew the fixing screws of the lower cover. Unscrew the two fixing screws of each side of the protective covers.
Assemble the throttle cable, spring, and throttle valve. Check the free travel in the throttle hand grip until you have Throttle Control. Remove the intake pipe mounting bolts. The air is forced to flow through cylinder fin and cylinder head. The throttle cable assembly splits into two cables with one end controlling the carburetor throttle cylinder and the other end controlling the quantity of oil delivered. Unscrew the fixing screws between the body cover and middle cover. Note: Before removing carburetor, you must shut the fuel flow off.
Disconnect the negative terminal of the battery, then disconnect the positive terminal. All you should do is browse our huge database of different books, and you are more than likely to find what you need. Pull out the worn speedometer cable. Always provide adequate ventilation during charging and maintenance of the battery. Inspect the spark plug wire for cuts, nicks or 2. The engine serial number is stamped on the left side of the engine crankcase. Disconnect the ignition coil primary wire.
Disassemble the idle jet, main jet, idle speed adjustment screw, and idle mixture adjustment screw. The torque drive pulley turns the belt. The answer is quite simple. Your Beamer requires a break-In period just as with all other internal combustion engines. Releasing the button will silence the horn. Keep away from sparks, open flame, and other possible sources of ignition.
Remove the cylinder carefully, so the whole piston is visible. Inspect the free play of the throttle lever. The drive shaft turns the idle gear in gearbox. The seal must be in good condition to insure a proper seal of the cap to the tank to prevent fuel spills. Torque value: M6: 5 — 8 lbf-ft M5: 3 — 4 lbf-ft Beamer Rev-2.
Turn the idle-speed adjust screw on the carburetor to obtain the idle speed. Place an oil catch pan under the unit plug in another ½ turn. If necessary, replace the rollers. Check the belt for wear. Unscrew the speedometer cable fixing bolt at the front wheel. See chapter 3 Disassemble the air cleaner and carburetor. Then remove the 2 10mm bolts from the exhaust pipe flange on the bottom of the cylinder.
To the left is the fuel gauge which indicates the fuel Ignition Switch level in the fuel tank. Unscrew two fixing bolts of the footrest board. In the event of a failure or required repair, the owner should take the vehicle to an authorized dealer for repair without undue delay and within a maximum of thirty 30 days of the occurrence of the problem. Then, hold the front brake level all the way in; while holding in, release the bleeder valve on the front caliper to force the air out. If the wheel rotates while the brakes are applied, check your fluid level and brake pads.