Depressurize it completely before removing the cover. The tow-rod or rope must be free from damage. Data included in other parts of the general documentation have been left aside. On completing the work, reassem- ble all protective devices, covers, and sound- and vibration-insulation material. Type rating plate of the machine. A table of contents is placed at the beginning of each section.
You can save a lot of money by working on your own vehicle as mechanics charge a lot. Damaged or missing heat shields must be repaired or replaced before the machine is put into operation. The Part Numbers given in the sec- tions are not to be used when order- ing spare parts. . Observe also the information set out in the Operator's Manual. Have any defects rectified immediately.
Risk of injury from hot or rotating parts in the engine compartment. Any work on receptacles that con- tain or have contained substances - that are flammable or encourage combustion, - that are susceptible to explosion, - that may develop noxious gases, fumes, vapours or dusts during welding operations may be performed only under expert supervision and only by experi- enced personnel authorized to do such work. Bring the welding current terminals as close as possible to the welding point. Risk of injury from falling loads or moving parts of the working equipment. Ensure that no connections are interchanged. They are specifically written for the do-it-yourselfer as well as the experienced mechanic.
If work is to be carried out close to overhead lines, the working equipment must be kept well away from them. Take the necessary precautions to ensure that the machine is used only when in a safe and reliable state. Insufficient tyre pressure means greater wear on the tyres and poor machine stabil- ity. Keep the signs clean and legible. Keep the first-aid box and the fire extinguisher readily accessible at all times. On deflection of the joystick handle into one direction, the distance of the annular magnet from the sensors located in movement direction is reduced or increased. Along with more than 672 pages of illustrations, that guide the reader through each service, repair and maintenance procedure.
Never look into the end of an inadvertently sev- ered fibre-optics cable, as that may severely injure the eyes. Clean the defective component carefully before dismantling it. Before starting work, familiarize yourself with the surroundings and circumstances of the site, such as obstacles in the working and travelling area, the soil bearing capacity and any barriers separating the construction site from the public highway. Ensure that the maintenance area is adequately secured. This may result in severe, poten- tially fatal injury. Oil, grease and other chemical substances When handling oil, grease and other chemical substances, observe the product-related safety regulations.
To avoid the risk of accidents, individual parts and large assemblies being moved for replacement purposes should be carefully attached to lifting tackle and secured. For detailed information refer to the Operator's Manual. Never remove lead seals from pres- sure-reducing valves and accumula- tors. Do not panic if the ground starts to give way and adequate withdrawal is impossible. Therefore: - Top up the batteries on well venti- lated premises only.
Slew the superstructure and drive the machine only after all per- sons have left the hazard zone. Data regarding auxiliary units for operating ancil- lary or special systems, as well as data on ma- chines produced only in small numbers, have not been included. This signs shows all control levers and pedals and the movements of the working equipment and the travelling gear initiated with these elements. Avoid any operation that might be a risk to ma- chine stability. Fastening means must be attached here when the machine is to be transported. It is this level of detail, along with hundreds of photos and illustrations, that guide the reader through each service and repair procedure. Checking the ignition key function: - If the engine is not shut off when fire breaks out, the fire will spread, impeding fire-fighting operations.
Use an exhaust pipe extension to remove the exhaust gases, or open doors and windows to let in suffi- cient fresh air. Working at the edge of excavations or on the verge of a road entails a risk of the machine overturning. Before setting the machine in motion, make sure that nobody is at risk. Close the front window and the cab door. Accumulators are installed in the hydraulic system. Carry out welding, flame-cutting and grinding work on the machine only if this has been expressly authorized, as there may be a risk of explosion and fire.
Take an alternative route with lower gradi- ents. The electrical equipment of machines is to be in- spected and checked at regular intervals. If incorrectly han- dled, however, there is a risk of ex- plosion. Why to buy Digital Service Manual from us? It is so strong that it may burn the skin, burn holes in clothing and, if splashed into the eyes, lead to blinding. Easy to read type,And give you all the information needed to do the procedure correctly. This sign indicates that the working equipment reaches far out over the machine and that it can be moved without moving the machine.
Note the position of the working equip- ment Never drive with the working equipment extended, as that may impair the stability of the machine. Do not allow persons to be trained or instructed or persons taking part in a general training course to work on or with the machine without being perma- nently supervised by an experienced person. Whenever you lose the manual we will replace for free within 24 hours. Working with the program, you can easily copy, save, and print the information you need. For do it yourself tractor parts lookup, parts manuals are key to viewing how everything goes together. Do not stand under suspended loads or under the work- ing equipment.