Loosen the clamp and remove the gasline hose from the delivery pipe of the throttle body assem- bly. If the brake fluid level is below the low mark, aim. Thread the spark plugs in part way; then while holding the head above the cylinder, carefully start and finger-tighten all four cap screws while observing the cylinder O-rings to make sure they remain in position. Some illustrations used in this manual are used for clarity purposes only and are not designed to depict actual conditions. Any older manuals floating around? The vast majority of sellers offering manuals online have little to no experience in the service industry whatsoever. High Beam by Arctic Cat Inc.
You will find all the Arctic Cat parts you need to have the best sled at Dennis Kirk. The Arctic Cat snowmobile manual by Clymer is the best reference book for repair and service information for your Arctic Cat snowmobile. Only genuine Arctic Cat parts, oil, and accessories are engineered to meet the standards and requirements of your Arctic Cat Snowmobile. It would be nice to have a cat book too. If clearance is not within speci- hole in the outer race is properly positioned and fications, replace the reed valve. Every Clymer snowmobile service manual contains hundreds of original photographs and illustrations obtained from the complete disassembly and assembly of the snowmobile covered. Remove the cable ties securing the throttle cable.
Will definitely recommend to friends. Be sure to position the ring with its tapered side up. . Lubricate the drive clutch bolt with a light film of pipe of the throttle body assembly; then secure oil; then place the drive clutch into position on the with the clamp. Idle Position Wide-Open Position 0. If we can provide additional assistance of any kind please feel free to and tell us what you need. Shut engine off and wait for all moving parts to stop.
Place new O-rings onto each of the head cap screws. Dennis Kirk began as one of the first aftermarket snowmobile parts retailers and we have continued to become the largest. All of the manual listed below are full factory service manuals with hundreds of pages containing step by step instructions, full wiring diagrams and detailed illustrations on how to repair, rebuild or maintain virtually anything to your sled. With our giant selection, you will be able to find all of the Arctic Cat replacement parts that you need to get your sled running like new again. Snap an old piston ring into two pieces; then grind the end of the old ring to a 45° angle and to a sharp edge. Do not idle the engine for excessively long periods of time. Verify ski alignment by measuring across from the outside edge of the left-side ski to the outside edge of the right-side ski without using the straight- edge in two places: approximately 35.
Start the engine and allow to idle. Remove the piston lock nut from the end of the shaft. If sealant gets into the hole, care- fully remove before proceeding. After downloading your Arctic Cat Snowmobiles service manual you can view it on your computer or print one or all of the pages needed. You can shop confidently with our 90 day, No Hassle Returns policy. Handlebar risers will put your bars right where they are most comfortable. If you need a hard copy, push the print button!! I'll have to give them a call and see what they have.
Thread the bearing assembly onto the shock body and hand-tighten until the O-ring is seated against the body. Clearance must be ing onto the crankshaft making sure the dowel-pin less than 0. If ski alignment is not as specified, adjust the of the track so it lies near the inside edge of the alignment of the ski s not parallel to the straight- left-side ski. Whatever drew you to your Arctic Cat, we know that you want to keep it running and looking the best that it can. This chart was compiled to assist technicians 2602-244 in fine-tuning the Arctic Cat rear suspension when the 2602-216 original springs are not optimum for the conditions 2602-254 and a softer or firmer ride is desired.
Service — replace hose — remove obstruction 4. I spent the better part of yesterday trying to track one down with no luck. It is fully printable, print 1 page, 1 chapter or print the entire manual and put it in a 3-ring binder. Using the Fuel Pressure Test Kit, connect the tes- ter to the delivery pipe and gasline hose. The meter must show 0.
Connect the two coolant hoses to the elbow fit- 8. Thanks Greg, I was pretty sure that wasn't the right manual. You have made my husband's day! Funoutfitters also has a manual but it seems pretty thin. It is about 100 pages in size dedicated to that sled and only that sled. Suspension Fully Suspension Fully 2703-385 13.